Xiaomi APN Settings for Telenor Norway

Xiaomi APN Settings for Telenor Norway (2026 Guide)

This guide provides the correct APN (Access Point Name) settings for Xiaomi, Redmi, and POCO devices on Telenor Norway. If your mobile data is not working, this guide will help you configure your device correctly.

Quick Overview

  • Primary APN: telenor.smart
  • Username & Password: Leave both blank
  • MMS Proxy: mms-proxy.telenor.no
  • MMSC: http://mmsc
  • APN Protocol: IPv4/IPv6

If your data is already working, you typically do not need to change these settings.

Quick Navigation

Before You Change APN: Diagnose First

Before manually changing APN settings, check if APN is likely the issue:

  • If your data is already working: Do not change APN settings.
  • If Wi-Fi works but mobile data doesn't: APN is one possible cause.
  • If the phone shows 4G/5G signal but no data: APN is one possible cause. Also check data balance, account status, and network provisioning.
  • If the APN currently set is telenor.smart and you have signal but no data: The issue may be with your subscription or network. Try resetting APN to default before manual configuration.
  • If APN is missing, incorrect, or was removed after a SIM swap/update: Manual configuration may be needed.

Why APN Settings Matter

APN settings act as a gateway between your Xiaomi device and Telenor's mobile network. Without the correct APN, your phone may not be able to access the internet or send MMS messages. While Telenor usually sends these settings automatically, manual configuration can be necessary after a software update, SIM swap, or if you are using a non-European ROM device.

Standard Telenor Norway APN Settings

The following settings are the standard APN configuration for Telenor Norway on Xiaomi devices, based on official Telenor documentation.

Mobile Data APN Configuration

  • Name: Telenor (or any name you prefer)
  • APN: telenor.smart
  • Username: (leave blank)
  • Password: (leave blank)
  • MCC: 242
  • MNC: 01 — This is the official Telenor value. If your Xiaomi does not save MNC 01, leave the field as automatically provided (see note below).
  • Authentication Type: Leave as default / not specified (do not change unless required)
  • APN Type: default,supl
  • APN Protocol: IPv4/IPv6

MMS Configuration (Optional)

  • MMSC: http://mmsc
  • MMS Proxy: mms-proxy.telenor.no
  • MMS Port: 8080
  • Combined format (if required): mms-proxy.telenor.no:8080

Step 1: Access APN Settings on Xiaomi

To configure APN settings on your Xiaomi, Redmi, or POCO device, follow these steps:

  • Open Settings on your phone.
  • Go to SIM cards & mobile networks.
  • Tap your Telenor SIM card.
  • Select Access Point Names (APN).

Step 2: Configure or Reset APN

You have two options at this stage:

Option A: Reset to Default (Recommended First Step)

If you see a list of APNs, tap the menu icon (three dots) and select Reset to default. This clears any corrupted settings and restores Telenor's automatic configuration.

Option B: Manually Add or Edit APN (Only if Reset Fails)

If resetting does not work, you can manually add a new APN:

  1. Tap the + (Add) icon.
  2. Enter the settings from the Mobile Data table above.
  3. Tap Save and select the new APN.
  4. Restart your phone.

Important: Only change the APN if resetting to default doesn't work. Leave other fields (MCC, MNC, APN protocol) as provided by your device.

MMS Settings (Optional)

If you are having issues sending or receiving picture messages, you may need to configure the MMS settings separately. Most modern devices handle this automatically.

Note: Some devices may require the MMS proxy and port to be combined as mms-proxy.telenor.no:8080.

Troubleshooting & Additional Notes

Xiaomi APN: MNC 01 Not Saving

Some Xiaomi users have reported that when manually entering the APN with MNC (Mobile Network Code) set to 01, the APN is automatically deleted or reverts to MNC 15 after saving. This is a reported behavior on some Xiaomi devices.

Important: The official Telenor MNC value is 01. However, if your Xiaomi device does not save this value correctly, you have two options:

  • Leave MNC as automatically provided – Do not force a manual entry. Let the device keep the default value it supplies.
  • Reset to default – Instead of manually entering the APN, try resetting the APN to default first.
  • Check for system updates – This behavior may be resolved in newer software versions.

Telenor vs MVNO

If your SIM is from an MVNO that uses the Telenor network (e.g., Talkmore, Happybytes), do not assume that Telenor's APN settings are correct for your subscription. Always check your specific provider's official APN settings.

5G and APN

The APN used for mobile data is generally not different simply because the phone connects over 5G instead of 4G. If 5G is unavailable, check network mode, coverage, device compatibility, and carrier provisioning before changing the APN.

After HyperOS Updates

After a major system update, check whether the Telenor APN profile is still present before manually creating a new one.

Frequently Asked Questions

What is the correct APN for Telenor Norway?

The standard APN is telenor.smart with no username or password. The MMS proxy is mms-proxy.telenor.no and MMSC is http://mmsc.

Why won't my Xiaomi save Telenor APN settings?

Some Xiaomi users have reported issues saving APN with MNC 01. Try leaving MNC as automatically provided, or reset APN to default instead of manual entry.

Why is my Xiaomi mobile data still not working after resetting the Telenor APN?

If resetting APN to default doesn't work, restart your phone. If the issue persists, contact Telenor to check your SIM provisioning and subscription status.

Do I need a different APN for 5G?

No. The APN used for mobile data is generally not different simply because the phone connects over 5G instead of 4G.

What should I do if Telenor APN reset does not restore mobile data?

If resetting APN to default doesn't work, try restarting your phone. If the issue persists, contact Telenor to check your SIM provisioning and subscription.

Note: This guide is updated for 2026. Menu names may vary slightly between HyperOS and MIUI versions. If you are using an MVNO, check your specific provider's APN settings.

Comments

Post a Comment

Popular Guides at UK Xiaomi

Xiaomi USB-C Earphones Not Working Issue Fix

Xiaomi USB-C Earphones Not Working Issue Fix – UK Guide If your USB-C earphones are not being recognized or have no sound when plugged into your Xiaomi, Redmi, or POCO device, this guide covers the most common reasons and how to fix them. Quick Answer: If your USB-C earphones aren't working, first check that the earphones work on another device. Then clean the USB-C port gently with a soft brush to remove dust or debris. Restart your phone and plug the earphones in again. If still not working, check USB audio routing in Developer Options (if available on your device). Applies to Redmi, POCO and Xiaomi Phones This guide applies to Xiaomi, Redmi and POCO devices running MIUI or HyperOS that use a USB-C port for audio, including devices without a 3.5mm headphone jack. 🔍 Quick Diagnostic Table What you see What it usually means Earphones not detected at all Port debris, ...
Read more

Xiaomi Audio Problems on HyperOS Devices Explained

Xiaomi Audio Problems on HyperOS Devices Explained – UK Guide HyperOS audio problems can affect the phone speaker, wired headphones, USB-C earphones, Bluetooth devices, microphones and car audio systems. Although many issues look similar, they usually have different causes. This guide helps you identify the symptom first, then directs you to the appropriate troubleshooting guide. Quick Answer: Most HyperOS audio issues are caused by incorrect volume settings, Bluetooth routing, Dolby Atmos, Bluetooth codec selection, equalizer settings, microphone permissions or hardware faults. Use the diagnostic table below to identify the correct troubleshooting guide. Start Here – Find Your Problem No sound at all → Go to Speaker & Headphone Audio Problems Bluetooth connected but silent → Go to Bluetooth Connected But No Sound Speaker too quiet → Go to Speaker Volume Low Bluetooth audio sounds poor → Go t...
Read more

Xiaomi Wired Earphones Not Detected on Xiaomi Phones

Xiaomi Wired Earphones Not Detected on Xiaomi Phones – UK Fix If your wired earphones are not being detected when plugged into your Xiaomi, Redmi, or POCO device, this guide covers the most common reasons and how to fix them. Quick Answer: If your wired earphones are not detected, first check they are fully inserted. For 3.5mm models, ensure the plug is firmly seated in the headphone jack. For USB-C models, check compatibility – most modern Xiaomi phones work with digital USB-C earphones with a built-in DAC, but analog models may not be supported. Test the earphones on another device, clean the port gently with a soft brush, and restart your phone. Applies to Redmi, POCO and Xiaomi Phones This guide applies to Xiaomi, Redmi and POCO devices running MIUI or HyperOS, covering both 3.5mm headphone jack and USB-C audio connections. USB Audio Architecture – A Quick Overview Understanding the basics of USB audio can help diagnose ...
Read more

Xiaomi Cannot Enable VoLTE in the UK

Quick Answer: If the VoLTE toggle is missing or greyed out on your Xiaomi in the UK, first dial *#*#86583#*#* (disables carrier check on some devices), then restart. After restart, go to Settings → SIM cards & mobile networks → [Your carrier] SIM → VoLTE should now appear. If still missing, contact your carrier to check VoLTE is correctly provisioned on your account or SIM profile (EE: 150, O2: 202, Vodafone: 191, Three: 333). Applies to Redmi, POCO and Xiaomi Phones This guide applies to Xiaomi, Redmi and POCO devices running MIUI or HyperOS, including models such as Redmi Note series, POCO X series, POCO F series and Xiaomi flagship devices (Xiaomi 14, Xiaomi 15, etc.). Check If Your Carrier Supports VoLTE EE, O2, Vodafone, Three, Giffgaff, SMARTY and VOXI all support VoLTE on many recent Xiaomi devices. If you're unsure, contact your carrier before continuing. Before Anything Else Check whether VoLTE is actually w...
Read more

Best Xiaomi Equalizer Settings for Bass

Best Xiaomi Equalizer Settings for More Bass (HyperOS & MIUI) If you want deeper, punchier bass from your Xiaomi, Redmi, or POCO device, the built-in graphic equalizer is the best place to start. This guide shows you how to access it and provides proven bass-boost settings for HyperOS and MIUI. Quick Answer: For deeper bass on Xiaomi devices, go to Settings → Sound & vibration → Sound effects → Graphic equalizer. Use a gentle "smile" curve: boost the lowest frequency bands by 3–6dB, keep mid bands neutral, and slightly boost high bands for clarity. Start with the preset profiles like Rock or Hip hop, then fine-tune manually to avoid distortion. How to Access the Equalizer on Xiaomi Open Settings . Tap Sound & vibration . Scroll down and tap Sound effects . Tap Graphic equalizer . Choose a preset or tap Custom to manually adjust the 10-band equalizer. Note: Depending on your Xiaomi model, the path may vary slightly. H...
Read more

Best Xiaomi Equalizer Settings for Gaming

Best Xiaomi Equalizer Settings for Gaming (HyperOS & MIUI) If you want better audio immersion and clearer positional cues in games on your Xiaomi, Redmi, or POCO device, the built-in graphic equalizer can help. This guide shows you how to access it and provides settings optimised for gaming. Quick Answer: For the best gaming audio on Xiaomi, go to Settings → Sound & vibration → Sound effects → Graphic equalizer. Boost the low frequencies (31Hz–125Hz) slightly for explosion impact, keep mids (500Hz–2kHz) neutral or slightly boosted for dialogue, and boost highs (4kHz–8kHz) for clearer footsteps. Also enable Dolby Atmos if available (select Game, Music, or Dynamic depending on your device), and use Game Turbo for per-game performance controls. How to Access the Equalizer on Xiaomi The equalizer is available natively on most Xiaomi, Redmi, and POCO devices running HyperOS or recent MIUI versions. No third-party apps are required. Open Settings . Tap So...
Read more

How to Exit Fastboot Mode on Xiaomi Phones

How to Exit Fastboot Mode on Xiaomi Phones (Step-by-Step MIUI Guide) Fastboot mode on Xiaomi devices, including Redmi and POCO phones running MIUI, is a useful tool for troubleshooting bugs or flashing custom ROMs. However, accidentally entering Fastboot mode is fairly common, and most users in the UK—whether in London, Manchester, or Birmingham—find themselves stuck and unsure how to exit safely without damaging their device. Why Accidental Fastboot Happens Fastboot mode can be triggered unintentionally if the power and volume buttons are pressed simultaneously during boot-up. While entering intentionally is part of advanced MIUI troubleshooting, unintentional entry usually leads to confusion, especially for less technical users who just want to use their Xiaomi as normal. Basic Method to Exit Fastboot Mode The simplest way to leave Fastboot mode on any Xiaomi, Redmi, or POCO device is straightforward: Press and hold the Power button for 10–15 seconds until the screen ...
Read more

Xiaomi Hotspot Works But Devices Have No Internet

Quick Answer: If your Xiaomi hotspot connects (laptop/tablet shows WiFi bars) but connected devices have no internet, first check Settings → Connection & sharing → Personal hotspot → Data limit → Set to "No limit". Then turn off Battery saver in Settings → Battery → Battery saver → OFF. If still not working, toggle Airplane mode on/off for 30 seconds. Applies to Redmi, POCO and Xiaomi Phones This guide applies to Xiaomi, Redmi and POCO devices running MIUI or HyperOS, including models such as Redmi Note series, POCO X series, POCO F series and Xiaomi flagship devices (Xiaomi 14, Xiaomi 15, etc.). Before Anything Else Open Chrome on your Xiaomi and check whether mobile data works directly on the phone. If mobile data does not work on the Xiaomi itself: Fix the mobile data problem first. Hotspot cannot work without mobile data. If mobile data works on the Xiaomi but connected devices have no internet:...
Read more

Xiaomi Dual SIM Not Working Properly? UK Fix Guide

Quick Answer: If you're having network problems with Dual SIM on your Xiaomi, first check that both SIMs are properly inserted and clean. Then go to Settings → SIM cards & mobile networks → SIM management → ensure your default SIM for data is set correctly. If issues persist, try swapping the SIM cards between slots as a troubleshooting step. Applies to Redmi, POCO and Xiaomi Phones This guide applies to Xiaomi, Redmi and POCO devices running MIUI or HyperOS, covering UK carriers including EE, O2, Vodafone, Three, Giffgaff, SMARTY, and others. 🔍 Quick Start – Find Your Path Symptom Most Likely Cause Go To One SIM has no signal but the other works fine SIM slot or SIM card issue Section 1 Mobile data is slow or drops when both SIMs are active Data SIM setting or network conflict Section 2 Calls drop or fail on one SIM VoLTE or carrier registration is...
Read more

Xiaomi Mobile Data Stops Every Few Minutes

This guide helps if your Xiaomi keeps losing mobile data connection every few minutes, the 4G/5G icon disappears and reappears, or internet stops working briefly and then comes back. Quick Answer: If your mobile data stops every few minutes on Xiaomi, first check that Battery saver is OFF (Settings → Battery → Battery saver). Also check that Data saver is OFF (Settings → SIM cards & mobile networks → [Carrier] SIM → Data saver). In many cases, these power-saving features are the cause. If still happening, go to Settings → Connection & sharing → Reset Wi-Fi, mobile networks, and Bluetooth – this often fixes intermittent data drops. Applies to Redmi, POCO and Xiaomi Phones This guide applies to Xiaomi, Redmi and POCO devices running MIUI or HyperOS, including Redmi Note series, POCO X/F series, and Xiaomi 14/15. 📊 Top Causes Ranking – Where to Start Not all causes are equally likely. Use this ranking to prioritise your trou...
Read more